Firmware Instruction « PLEXTALK Americas English main

main contents

Step 1: Download file and create installation CD.

Start Nero Burning ROM Ver.5.5.
Select “Open” from “File” pull-down menu, then the common dialog pops up.
In the common dialog, change “File of type” to “Image Files(*.nrg;*.iso; *.cue)”.
Start CD burning.

Start WinOnCD3.70.
Select New from File menu, then New project dialog will be popped up.
Change the tab from Favorites to “Other”, and select Track image.
Select Track Image and press OK button, then will be returned to the main window.
Select ISO image file in the explorer window, and press F7 key.
Select Make CD from Record menu, then Disc Properties and Recording Settings dialog will be displayed at the lower window.
Press the Record button, or Alt + R key, then start burning CD. Note: You can be setting up the recording setting at the lower windows when required.
After writing process completed, message window will be popped up.

Step 2: Install Firmware into PLEXTALK PTN1/PTR2/PTR1.

In case of PTN1

Connect AC adaptor.
Turn on the PLEXTALK PTN1.
Insert installation CD.
The installation process will be executed automatically and takes approximately 3 minutes.
When upgrade installation is completed, PTN1 will automatically re-boot and eject the CD.

In case of PTR2

Disconnect USB cable.
Connect AC adaptor.
Turn on the PLEXTALK PTR2.
Insert installation CD.
Press play key.
The installation process will be executed automatically and takes approximately 3 minutes.
When upgrade installation is completed, PTR2 will automatically re-boot and eject the CD.

In case of PTR1

Remove PC card and disconnect USB cable.
Connect AC adaptor.
Turn on the PLEXTALK PTR1.
Insert installation CD.
Press play key.
The installation process will be executed automatically and takes approximately 3 minutes.
When upgrade installation is completed, PTR1 will automatically re-boot.
Remove installation CD.

Step 1: Download file

Step 2: Install Firmware into PLEXTALK

In case of PTR1

Connect the PTR1 to AC power using the PTR1 power adapter.
Remove the PC card, if one is inserted in the unit.
Turn on the power and eject CD, if one is loaded.
Connect the PTR1 to your PC using the supplied USB cable.
Execute the downloaded file (PTR1USBUP204***.exe), from the saved to location of your PC.
Proceed with the installation, following the instruction provided on your PC’s screen.
Note: During the updating process, you will see the following message: “Shut down”. The process is still updating your PTR1′s internal program. Do not operate the PTR1 until you receive further messages, presented on your PC, instructing you to do so.
Press OK after the following message is displayed on your PC “In order to finish the update, you need a turn off your PC then remove the USB cable from PTR1. Could you turn off the PC now?”
You may, now, turn off the PC and disconnect the USB cable from your PC. The update is completed.
Note: All memory is refreshed and bookmarks have been deleted when you upgrade from Version “1.**” to “2.**”.

In case of PTR2

Connect the PTR2 to AC power using the PTR2 power adapter.
Turn on the power and eject CD, if one is loaded.
Set the USB destination to “CD drive” in the PTR2 control panel menu.
Connect the PTR2 to your PC using the supplied USB cable.
Execute the downloaded file (PTR2USBUP108***.exe), from the saved to location of your PC.
Proceed with the installation, following the instruction provided on your PC’s screen.
Note: During the updating process, you will see the following message: “Shut down”. The process is still updating your PTR2′s internal program. Do not operate the PTR2 until you receive further messages, presented on your PC, instructing you to do so.
Press OK after the following message is displayed on your PC “In order to finish the update, you need a turn off your PC then remove the USB cable from PTR2. Could you turn off the PC now?”
You may, now, turn off the PC and disconnect the USB cable from your PC. The update is completed.

SUPPORT